Description

See pictures for an example of what you will receive. One (1) O.E.M. Original Equipment Manufacturer Factory remote keyless entry fob alarm controller Transmitter control clicker keyfob controller replacement FCC ID # : A269ZUA111 PART#: 88035AC230 or 88036AE060 or 88035AC231 Frequency : 315 Mhz Canda: 700 101 672 MADE IN JAPAN Battery: 1 ;CR2032 (installed) Buttons : 2: Unlock/Disarm, Lock/Arm/Panic (Buttons will be :Gray or Orange & Blue) See Item Specifications for more details Compatible Vehicle’s 2003 2004 2005 2006 Subaru Baja 1999 2000 2001 2002 2003 2004 2005 Subaru Forester 2001 2002 2003 Subaru Impreza 1999 2000 2001 2002 2003 2004 Subaru Legacy 1999 2000 2001 2002 2003 2004 2005 Subaru Outback 1999 2000 2001 2002 2003 2004 2005 Subaru Impreza WRX PROGRAMMING INSTRUCTIONS: FCC ID A269ZUA111 ALPINE SYSTEM 1999 Legacy only: Passive arming of the optional 1999 alarm system. The dealer could program the alarm to arm automatically whether the doors are locked or not. In this mode the doors must be manually locked or using the power lock button or the remote. In Passive Mode the system will automatically activate in one minute but will not lock the doors. it will arm the alarm even if the doors are not locked. Lock the doors using the power lock switch with the door open. If you are using the remote to lock the doors, there would be no reason to set Passive Mode because locking with the remote would arm the alarm anyway so I'm not sure why this function exists.... To open the doors use the remote or the key, but then the alarm will go off and you'll need To set Passive Mode: Open driver's door and remove the plastic step sill that curves up toward the front. Connect the single-pole white connectors. the plain gray buttons were used 99-01, colored buttons for 2002-04 replacement note: this style remote has been discontinued and replaced by the new style in late 2009. See your local dealer. How To Use The Alpine Alarm Battery #CR2032. Range? App 50ft. Battery fade, other cars, buildings, walls etc affect range. 1. Locking. Push the large button. This locks all the doors and will set the alarm (if equipped and in setable mode). 2. Unlocking. Push the small button once to unlock the driver's door and disarm alarm, if set. Push the small button a second time to unlock all the doors. 3. Honking horn? On 1999-2002 models the horn honks once for lock and twice for unlock, 3 times if a door is not closed. This audible honk feature is optional. To turn it off or to turn it on unlock all the doors and hold *both* buttons down until the horn honks once. The horn will always honk 3 times if a door is not fully closed when you lock it. This was changed in 2003, models to a 'chirp'. There is no longer an audible honk feature. If a door is ajar the system will chirp 5x and the lights flash. 4. Alarm. (optional) System chirps when locked with the remote if you have an alarm, and no you can't turn the chirp off. 5. Valet mode or alarm off: alarm light (red dot center dashboard display) rapidly flashing 3 times means the alarm is in "Valet" mode and is not setable. The light will stop flashing when you start the car. To set valet mode or just to disable the security alarm system: 1. unlock all doors 2. physically open the driver's door 3. hold the UNLOCK button on remote for 2+ seconds or so. The red 'security' light will then flash 2 times a second until the car is turned on. 6. Arming the alarm: to make an alarm in valet model arm-able, unlock all the doors and hold the small button down on the remote until the light stops flashing. Now when you lock the doors the alarm will be set and the light will flash on and off, on and off. 7. Alarm goes off? Push the small button on the remote OVERRIDING the alarm when you don't have a Remote to disable it. If you don't have the remote put the key in the ignition and turn it on and off three times and the car will start on the 4th time 8. Program remotes: works on Alpine system. Unlock all doors, foot on brake, all doors closed. Cycle key quickly but carefully on-off appr 10 times until the car honks one time. Do not turn the key far enough to start the car, just to the 'on' position so the dashboard lights up. When the horn honks, open and close the driver's door, press any remote button and that's it. Program another remote? Quickly open and close the driver's door again and push a button on the 2nd remote. That's it. When you're done, remove the key and the horn should honk 3 times. You're all set. Sometime it takes more than 10 on-offs to set program mode. Open/close the door, lock/unlock etc, wait 10 minutes, then try again How to find out if this remote is compatible with your Vehicles’ installed RKE System If you're not sure your vehicle can use this remote, please ask questions or contact your local dealer first. 1. Check the back of your current or old keyless remote to match FCC ID /Part #’s. 2. Contact your local dealer and tell them your VIN# and ask what part # / FCC ID you need. Your vehicle will be installed with one of the following keyless entry systems: a. Standard Keyless Remote Packages: Installed at time of manufacture. b. Optional Keyless Remote Packages: Installed by a dealer. c. Aftermarket Keyless Remote Packages: Installed by previous owner or a car/audio shop. d. No remote keyless entry system at all. The above information can change which remote you need for your installed remote keyless system . Payment : We accept payment via PayPal or Credit Card. Please contact us via eBay messages for any questions concerning payments. Payment is expected within 5 days PA SALES TAX : As per the State of PA Franchise Board we must collect sales tax from PA Residents for any purchase made from our store. Contact/Email : Due to scams etc, we DO NOT respond to emails. We only read/respond to EBAY MESSAGES . Messages & Best Offers are checked throughout the day & we typically respond 7 days a week. Please contact us with questions via eBay messages (keyless4u). 100% Guarantee Remote Shipping / Return Policy Warranty/Returns : 1. We have a 30 day return policy. 2. All returns for replacements and refund need an RMA #. 3. Please contact us before returning items so we can give you the RMA # and the proper return address. 4. No refunds / replacements will be granted without an RMA# We ensure proper working condition of all previously used or new remotes through a serious of tests performed with the Santronics Testing device. Each button is tested for functionality prior to shipment and then logged. Please Note : Each remote and circuit board is UV ID’d prior to shipment – All returns receive a UV ID inspection to verify originality of remote sent prior to refund or replacement. Does this keyless remote entry come with a battery? Yes . It will have a working battery installed. Battery Condition: A. All remotes sold on Keyless4u include working batteries. B. Installed batteries are not tested for battery life- they are simply working. Some are new and some are used.